1. Design & Engineering

• Verification and optimization of Heat gain and cooling load calculations in accordance with ASHRAE standards.
• Verification and optimization of Smoke management system design and calculations in compliance with local authority and Civil Defense requirements.
• HVAC system selection, zoning, and configuration to ensure optimal thermal comfort, energy efficiency, and operational reliability.
• Verification and optimization of industrial kitchen extracting system
• Verification and optimization of Indoor environmental design criteria in accordance with project specifications, including:
  
  • Temperature and relative humidity requirements
  • Noise criteria (NC/NR levels) for all conditioned spaces
  • Indoor air quality (IAQ) and fresh air ventilation requirements
• Preparation and submission of detailed HVAC drawings, including:
  
  • Equipment layout drawings
  • Ductwork layouts with sizing and routing
  • Chilled water and/or refrigerant piping layouts
  • Control schematics and detailed sequences of operation
• Selection of HVAC equipment with high energy efficiency ratings and compliance with sustainability requirements.
• Full coordination with architectural, structural, electrical, plumbing, fire protection, fire alarm, and BMS systems.
• Compliance with all applicable local authorities’ regulations and international standards.
• Value engineering proposals to optimize capital cost, operating cost, and energy consumption without compromising performance or quality.

2. Supply of Equipment & Materials

HVAC Equipment

• Chillers / VRF systems / Packaged units (as applicable)
• Air Handling Units (AHUs) and Fresh Air Handling Units (FAHUs)
• Fan Coil Units (FCUs), cassette units, and ducted indoor units
• Exhaust, ventilation, and pressurization fans
• Ecology Units

Ductwork Systems

• GI , PI, fire rated,  MS, and SS ductwork complete with thermal and acoustic insulation
• Volume control dampers, fire dampers, smoke dampers, and motorized dampers

Piping Systems

• Chilled water pumps complete with valves, accessories, and controls
• Chilled water heat exchangers complete with valves, accessories, and controls
• Chemical dosing system complete with valves, accessories, and controls
• Chilled water piping with all required valves, fittings, and accessories
• Thermal insulation and protective cladding

Air Distribution & Controls

• Diffusers, grilles, registers, and louvers
• HVAC control components including thermostats, sensors, actuators, and control panels
• Integration with BMS, GRMS, and Home Automation systems
• Vibration isolators, noise attenuators, and acoustic treatment as required

3. Installation & Construction

• Installation of all HVAC equipment in accordance with approved shop drawings and manufacturer recommendations.
• Fabrication and installation of all types of ductwork systems, including hangers, supports, and accessories.
• Installation of chilled water and refrigerant piping systems with proper supporting and insulation.
• Installation of air distribution devices, dampers, and balancing devices.
• Installation of HVAC-related electrical power wiring and control cabling.
• Installation and integration of control systems with BMS, GRMS, and Home automation systems.
• Coordination with all trades to avoid clashes and ensure smooth execution.
• Implementation of approved safety procedures, quality control, and inspection plans throughout construction.

4. Testing, Inspection & Pre-Commissioning

• Pre-commissioning inspection and verification of all HVAC systems and equipment.
• Pressure testing, flushing, and chemical cleaning of chilled water systems.
• Duct leakage testing in accordance with project specifications and standards.
• Testing, adjusting, and balancing of air and water systems to achieve design flow rates.
• Measurement and verification of:
  
  • Space temperature and relative humidity
  • Noise levels within conditioned areas
  • Functional operation of controls, interlocks, and safety devices

5. Commissioning & Authority Approval

• Start-up and commissioning of all HVAC equipment and systems.
• Performance testing to confirm compliance with design criteria and specifications.
• Demonstration of system operation under various load and operating conditions.
• Coordination with consultants and authorities for inspections, testing, and approvals.
• Rectification of any deficiencies identified during commissioning or authority inspections.

6. Documentation, Training & Handover

• Submission of complete as-built drawings and final HVAC layouts.
• Submission of Operation & Maintenance (O&M) manuals.
• Submission of test reports, warranties, certificates, and equipment datasheets.
• Training of client and facility management personnel on system operation and maintenance.
• Final handover of the HVAC system in a fully operational, tested, and approved condition.